Draper SC1 Manual de instrucciones descargar pdf (Pagina 3)

Installation Tips

Motor Testing

It is recommended to test and set all motor limits prior to electrician wiring motor. Draper sells a test cord, C116.014, for this. Testing and

setting limits on all motor types before the electrician wires the motor is helpful in ﬁ nding problems before the motor has to be disconnected

from electricity. Motor can lose their limits in shipping even if they are set at Draper, Inc.

Shimming

This is an installation practice used in the ﬁ eld to correct fabric tracking. Shade fabrics are not smooth surfaces so as they roll on them-

selves, then they will want to walk left or right. Correcting this tracking can be done through shimming. You increase the diameter of one side of

the shade by adding tape which will draw the fabric towards the applied tape. To shim, you will run the fabric down to where it is attached to the

roller. You will then apply an 1” square piece of duct tape to the roller with half on the roller and half on the shade cloth to the outside edge of the

cloth. You may apply up to three pieces in an overlapping fashion on top of each other to help more severe tracking issues. The larger the piece

of duct tape and the more toward the outside of the roller the tape is attached, then the more the fabric will move to that side.

How to Measure for Draper Shades

FlexShades are custom fabricated for

each opening, and must be measured ac-

curately.

Determine the area to be covered, and

decide where brackets or endcaps will be

attached.

Be careful to allow for any irregularity

which will interfere with the proper operation

of the unit (i.e. handles, irregular trim, locks or

opening not square and plumb).

Inside Mount

1. Measure from six positions at each

window—top, center, and bottom for

the width; left, center, and right for the

height.

2. Measure the width of the opening,

providing Draper with the EXACT win-

dow opening width at the window’s nar-

rowest point. DO NOT MAKE ANY

DEDUCTIONS for bracketing or

mounting—Draper will make the neces-

sary deductions.

3. Measure the height of the opening,

providing Draper with the EXACT win-

dow opening height at the window’s

shortest point. Again, DO NOT MAKE

ANY DEDUCTIONS—Draper will take

the appropriate deductions.

4. Note for Inside Mount Lightbloc

Shade—Draper will take the appropri-

ate deductions from your EXACT

OPENING dimensions in both width

and height.

Outside Mount

1. Measure the width of the window,

specifying the EXACT width and height

you want the product to be. Draper

will make your product to the exact

size you specify. NOTE – adding

overlap to a shade increases privacy

while decreasing light leaks.

2. Note for the Outside Mount Lightbloc

Shade – Draper will fabricate the unit to your

EXACT OVERALL dimensions, taking no

deductions. Make sure to account for the side

and sill channels.

Cloth Measurement: Exact width of cloth.

Depending on product, overall width may be

wider than fabric.

Pocket: If mounting shade brackets or

headbox in a pocket above window opening,

give the exact overall height (top of pocket to

sill) and the exact width of pocket. Draper will

make necessary deductions.

Seams: As standard, shades that are both

wider and taller than the maximum available

fabric width in any given style will be seamed

horizontally (“transversed” or “railroaded”) at

Draper’s discretion with the seam placed as

high as possible (from the bottom of the shade

up) unless otherwise speciﬁ ed.

Stays: Draper may, at our sole discretion,

add stays to the shade in pockets or at seam

locations to improve surface ﬂ atness and

reliable operation. Stays are made of spring

steel and measure ¼” wide and are inserted

in pockets in the fabric measuring approxi-

mately 11/8” wide. Shades over 10’ wide OR

over 14’ in height will have stays placed at in-

tervals of no more than 96” (Colossal shades

taller than the widest fabric width have stays

at intervals of no more than 63”).

Note for LightBloc and Skylight Systems:

IM LightBloc—Draper will deduct 1/8” from

your exact opening dimensions in both width

and length. Be sure several measurements

are taken to discover any irregularities in the

opening.

IM Skylight—Draper will deduct 3/4” from

your exact opening dimensions in both width and length. Draper provides angles to be installed

around the opening and the shade rests on the angles. Be sure several measurements are

taken to discover any irregularities in the opening.

OM LightBloc and Skylight—Draper will fabricate the unit to your exact dimensions, taking

no deductions.

Note which units, if any, abut at mullions.

Inside Measure

Outside Measure

www.draperinc.com

(765) 987-799

Page 3 of 120

1 2 3 4 5 6 7 8 ... 119 120

Comentarios a estos manuales

Sin comentarios

Draper SC1 Manual de instrucciones Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para No Draper SC1