Draper Silhouette/Series V Instrucciones de operaciones descargar pdf (Pagina 3)

220V Silhouette/Series E & V by Draper

Page 3 of 5

Adjustments

Please Note: Screen limits are factory set for optimum performance of the

screen. Any adjustment of these limits could void the warranty. Please

check with Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in “off” position before ad just ing limit

switches.

Adjusting “fully up” position — “Up” stopping position may be ad just ed by

turning the yellow limit switch adjustment socket. The yellow socket is located

on left end of screen roller. Turn ing the socket coun ter clock wise will allow the

view ing surface to retract farther into the case. Turn ing it clockwise will cause

the sur face to stop farther out of the case. One full revolution of the socket will

alter the stop ping position of the view ing surface by ap prox i mate ly 25 mm (1").

Adjusting “fully down” position — “Down” stopping position may be ad-

justed by turning the white limit switch adjustment socket. The white socket is

located on the left end of screen roller. Turning the socket coun ter clock wise

will allow the viewing surface to run farther down. Turning it clockwise will

shorten the viewing surface, causing it to stop in a less extended position.

AT NO TIME SHOULD VIEWING SURFACE BE UNROLLED ENOUGH TO

EX POSE ANY PART OF SCREEN ROLLER.

① Determine which side requires adjustment.

② Secure dowel with one hand.

Caution: Do not touch or bend surface.

③ Using Philips-head screwdriver, depress spring-loaded adjustment screw

(see drawing) and slowly turn clockwise to tighten tension, or counter-

clockwise to loosen tension. The screw adjusts in ¼ turn increments.

Adjust only one increment (¼ turn).

④ If problem is not corrected, leave screen in position for 24 hours to allow

surface material to stretch into position.

⑤ If problem still is not corrected, repeat steps ② and ③.

Dowel

Adjustment

Screw

Tensioning

Cable

www.draperinc.com

(765) 987-799

Tab-Tension Adjustment Procedure for Silhouette/Series V

Caution: Do not remove the roller assembly from the

case unless necessary for repairs. If the roller

assembly is removed, be sure motor is fully re-seated

in the bracket, and re-secure it carefully with the motor

retaining spring (see diagram at right).

Limit Adjustments (Built-in Low Voltage Motors)

Please Note: Screen limits are factory set for optimum performance of the

screen. Any adjustment of these limits could void the warranty. Please

check with Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in “off” position before ad just ing limit

switches.

① Connect the ILT switch to the motor via the terminal blocks, or via the

modular port using four conductor modular cable. When using modular

cable, the cable connectors MUST NOT be crimped in reverse, as with

standard telephone cable.

② Set the slide switch to the lower position. Press and hold the DOWN button

on the switch to move the viewing surface to the desired lower limit. If the

screen moves in the opposite direction, release the DOWN button and

press and hold down the STOP button for four seconds. This will reverse

the operation of the UP and DOWN switches.

③ Move slider switch into center position.Wait a couple of seconds.

Please Note: If you move the slider switch from down to up in one mo-

tion it sets the two limits in the same postion.

④ Set the slide switch to the higher position. Move the viewing surface to the

desired upper limit by pressing and holding the UP button on the wall

switch.

⑤ Return the slide switch to the center position to return to normal operation.

⑥ To set the viewing surface to an alternate format position, move the viewing

To Motor

with

Built-In

Low Voltage

Slide

Switch

Back View

To Motor

with

Built-In

Low Voltage

POSITION

FUNCTION

DOWN

CENTER

Set LOWER limit

Set UPPER limit

Normal Operation

STOP

surface to the desired position and press the STOP button. Press and hold

the STOP button for at least three seconds to record the position.

Please Note: Pressing and releasing the UP button on the switch will move

the screen to its upper limit. Pressing and releasing the DOWN button will

move the screen to its lower limit.

While the motor is in motion, pressing the STOP button for less than two

seconds will stop the viewing surface at its present position.

Once the motor is stopped, pressing the STOP button will move the view-

ing surface to its alternate format position.

Pressing and holding the STOP button, when the motor is at rest or in mo-

tion, for at least three seconds will record a new alternate format position.

1 2 3 4 5

Comentarios a estos manuales

Sin comentarios

Draper Silhouette/Series V Instrucciones de operaciones Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Pantallas de proyección Draper Silhouette/Series V