Draper MC1 Manual de usuario Pagina 2

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 9
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 1
MC1 V3 Installation & Programming page 2 / 9
This Sheet uses # for the receiver's main channel number - new units will use a 1 where the # is.
Note that # can also be ALL if you want to program several receivers S = Stop C = Close O = Open
Desired Change LED: on blink blink off
Reset EVERYTHING to factory default S+7+7 O ALL hold 5 sec. until blink S
Reset everything except main channel to factory default S+7+7 O # C ALL S
Main Channel to “N” (N= 1 through 60) S+7+7 O # C 1 O “N” S
1
st
Group Channel to “N” (N= 1 through 60) S+7+7 O # C 2 O “N” S
1
st
Group Channel OFF S+7+7 O # C 2 O ALL S
Set 2
nd
Group Channel (same as above) S+7+7 O # C 3 O “N” S
Set 3
rd
Group Channel (same as above) S+7+7 O # C 4 O “N” S
Set 4
th
Group Channel (same as above) S+7+7 O # C 5 O “N” S
Set 5
th
Group Channel (same as above) S+7+7 O # C 13 O “N” S
Set 6
th
Group Channel (same as above) S+7+7 O # C 14 O “N” S
Set “Sequential Action” Channel (same as above) S+7+7 O # C 20 O “N” S
Set “Specific Stop” Channel (same as above) S+7+7 O # C 22 O “N” S
Reset the following options to factory default S+7+7 O # C 6 O ALL S
Momentary Motor Action
2
S+7+7 O # C 6 O 1 S
Reverse Motor Direction S+7+7 O # C 6 O 2 S
Do NOT Act on ALL buttons from Transmitter S+7+7 O # C 6 O 3 S
Fast IR Release Time
2
S+7+7 O # C 6 O 7 S
Stop On Transmitter Button Release
1
S+7+7 O # C 6 O 8 S
Demo mode on: quick deadbeat
10
S+7+7 O # C 6 O 9 S
Disable the Deadbeat Counter S+7+7 O # C 6 O 11 S
Enable the Deadbeat Counter, and reset it to 120
10
S+7+7 O # C 6 O 12 S
Reset the following options to factory default S+7+7 O # C 7 O ALL S
SPST Manual switch
3
S+7+7 O # C 7 O 1 S
X10 Timing on Manual Switches S+7+7 O # C 7 O 2 S
Stop On SPDT Manual Switch Release
1
S+7+7 O # C 7 O 3 S
“Sticky” action on SPDT Manual Switches
1
S+7+7 O # C 7 O 4 S
Swap Open and Close on SPDT, Invert SPST S+7+7 O # C 7 O 5 S
Enable SPST Magnetic Switch as Override
3
S+7+7 O # C 7 O 6 S
Set the Run Time to 100x+10y+z seconds
min = 0 0 1 (1 sec), max = 2 9 9 (299 sec) use O10 for 0
S+7+7 O # C 8 Ox Oy Oz S
Reset the following options to factory default S+7+7 O # C 23 O ALL S
Enable “Sticky” on main channel
1
S+7+7 O # C 23 O 1 S
Enable “Sticky” on 1
st
group channel
1
S+7+7 O # C 23 O 2 S
Enable “Sticky” on 2
nd
group channel
1
S+7+7 O # C 23 O 3 S
Enable “Sticky” on 3
rd
group channel
1
S+7+7 O # C 23 O 4 S
Enable “Sticky” on 4
th
group channel
1
S+7+7 O # C 23 O 5 S
Enable “Sticky” on 5
th
group channel
1
S+7+7 O # C 23 O 6 S
Enable “Sticky” on 6
th
group channel
1
S+7+7 O # C 23 O 7 S
Turn OFF “Sticky” action on ALL buttons
1
S+7+7 O # C 23 O 8 S
Vista de pagina 1
1 2 3 4 5 6 7 8 9

Comentarios a estos manuales

Sin comentarios