Draper SC1 Manual de instrucciones descargar pdf (Pagina 55)

Installation Instructions

™

R2D7 RS232 Professional Integration Interface by Draper

If you encounter any difﬁ culties installing/wiring your IntelliFlex

RS232 Professional Integration Interface, call your dealer or

Draper, Inc., Spiceland, Ind., (765) 987-7999; fax (765) 987-7142;

or e-mail [email protected].

To Bus System 7 (or to RF Transmitter)

To Bus System 6

To Bus System 5

To Bus System 4

To RS232 Port:

Yellow = Rx (Receive data from control system)

Green = Tx (Transmit data to control system)

Red = Unused

Black = Gnd (Signal Ground)

To Bus System 1

To Bus System 2

To Bus System 3

Serial Port to Motor Link

Information Data Number of characters

Header (Start of command) * (asterisk) for use on RP B US 1

Subsystem number or

Administration command

– 7 if BUS, 7 – 99 if Radio

= report version

R = make port 7 Radio

B = make port 7 BUS

1 or 2

Command

o = open c = close s = stop

p = program q

= quit sending

Channel

–60

Time to send

10 11

0 0 0

– 9 9 9 20

of seconds

(this value is optional) 3

Terminator ; (semicolon) or “ CR” (enter key) 1

Pause Send a command on an unused channel for the desired pause

time.

Motor Link to Serial Port

Event R2D7 sends

Powered up “ version, X -on”

Terminator is received

“ LF” if good command

“U” sent if command cannot be understood

“ CR” is sent after command has been relayed to motors

Buffer

overflows and all data is purged “O” is sent

Buffer is half full “X -off ” (Ctrl -S)

Buffer is empty “X -on” (Ctrl -Q), but only if X -off was previously sent

Special characters

Character Description

ASCII Character Number

“ ; ” Semicolon, signifies end of command 59 (0x3B)

“ CR ” Carriage return, signifies end of command 13 (0x0D)

“ * ” Asterisk, Shift 8 on most keyboards 42 (0x2A)

“ LF ” Line feed, ignored (not used) 10 (0x0A)

“ X -off ” Ctrl -S on most keyboards, requests sender to stop sending 19 (0x13)

“ X -on ” Ctrl -Q on most keyboards, requests sender to resume sending 17 (0x11)

1. Total message length may be as short as 2 and as long as 10 characters, typically 6.

2. 0 means ALL systems, for super groups ALL does not include the radio channels.

3. Version reports “2.1” then R if administered as Radio, or B if BUS, followed by carriage return (All characters after V in this command are ignored).

4. Radio requires a RF TM be plugged into port 7 jack.

5. Case is important: o is different from O and so on.

6. Stop sending a forever command. Any other command will stop transmission, but an error will be reported.

7. If command is stop or quit, then this value is optional and ignored.

8. 00 = ALL.

9. 60 = “cut strap ALL” (note that version 2.0 used 25 for this channel).

10. If no digits, then the command is sent for 2 seconds, except for stop and program which are sent for ¼ second.

11. Time between commands = .5 sec if multiple commands are buffered (Time = .1 sec after a stop).

12. 000 = Forever, use the q command to stop transmission.

13. Max timed pulse = 50 sec. If this is a radio command, the value is rounded up to the nearest 10th second.

14. Buffer is 120 bytes long.

Please Note

➀

Includes free “GUI” software capable of scheduling timed events and

global alignment positioning of shades.

➁

For information on programming and operation, see IntelliFlex

Programmer instructions available at www.draperinc.com.

➂

This input device can be used with SC1, SGC4 or SPGC4.

Serial Port Adapter

Converts a standard DB9 serial output of

a PC into an RJ11 connection providing

RS232 serial commands.

USB-to-DB9 Serial Port Converter

Serves as a bridge between USB port and

standard RS232 Serial Port.

You may also need ...

Codes and Technical Information

Page 55 of 120

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 119 120

Comentarios a estos manuales

Sin comentarios

Draper SC1 Manual de instrucciones Pagina 55

Comentarios a estos manuales

Relacionado con productos y manuales para No Draper SC1